Model B Caliper
(2 Piston)...
Compact and lightweight describes this modern design's best features. Two 1-5/8" centerless ground pistons hard anodized for long wear and performance. Top quality organic brake pads are featured on each caliper. Clear anodizing seals the aluminum housing for a long life and lasting luster. The proper bracket is included for each application.
GMA 200E
|
|
|
GMA 200E |
GMA 200E-B |
GMA 200E-C |
Classic Clear Anodized |
Classic Black |
Classic Chrome |
|
|
GMA 200E-SB |
GMA 200E-SC |
Smooth Black |
Smooth Chrome |
|
Front Single Disc FX & Sportster
Models 1974-Early 1977
A dramatic improvement over the original OEM brake. Fits front single disc FX and Sportster® models 1974 to early 1977. Contains all the necessary parts, including mounting hardware, spacers and bracket. Will require removal of the rotor from the hub and spacing the rotor for adequate caliper-to-spoke clearance. These spacers are included with the kit. A fitting is provided to adapt to the stock brake line.
Designed for wheels 19" or smaller.
Kit requires a 5/8" bore master cylinder.
GMA 200F
|
|
|
GMA 200F |
GMA 200F-B |
GMA 200F-C |
Classic Clear Anodized |
Classic Black |
Classic Chrome |
|
|
GMA 200F-SB |
GMA 200F-SC |
Smooth Black |
Smooth Chrome |
|
Front Single Disc, All Models,
1984-1999
Fits all models from late 1984 to 1999. New one piece design bolts directly to lower leg, eliminating the need for a bracket. Kit requires 5/8" bore master cylinder for single disc and 3/4" bore for dual disc. Will not fit Narrowglide 21" wire wheel. This kit is designed to accept 10mm (3/8-24) banjo bolt.
GMA 200DD
|
|
|
GMA 200DD |
GMA 200DD-B |
GMA 200DD-C |
Classic Clear Anodized |
Classic Black |
Classic Chrome |
|
|
GMA 200DD-SB |
GMA 200DD-SC |
Smooth Black |
Smooth Chrome |
|
Fits FL, FLH, 1949-1984
Designed for the custom builder
A modified version of the GMA B caliper family is designed with the custom builder in mind. This is not a direct bolt-on kit. Removal of the original factory brake mounting tabs may be required. Converts OEM drum brake front end to 10" dual discs. Bolt-on dual disc kit mounts to original fender mounts. All mounting hardware and brackets are included. Kit includes aluminum spacers for mounting either the narrow, custom after-market fender or the OEM 16" fender. 16" or 19" wheels only. The kit requires 3/4" bore master cylinder.
GMA 200P
|
|
|
GMA 200P |
GMA 200P-B |
GMA 200P-C |
Classic Clear Anodized |
Classic Black |
Classic Chrome |
|
|
GMA 200P-SB |
GMA 200P-SC |
Smooth Black |
Smooth Chrome |
|
Front Single Disc,
Fits Paughco Brand #181
Wide Springer Front Ends
Use Paughco Axle Kit #186A, 1984 to 1999, single flange hub, FXST or FXWG. If FXWG hub is used with Speedo drive, the non-flange side must be notched to accept the tab. For use with 11.5" rotor. Includes bronze washers, rod ends, axle spacer and bushings. Not designed for use with Paughco fender 182A.
GMA 200S
|
|
|
GMA 200S |
GMA 200S-B |
GMA 200S-C |
Classic Clear Anodized |
Classic Black |
Classic Chrome |
|
|
GMA 200S-SB |
GMA 200S-SC |
Smooth Black |
Smooth Chrome |
|
Front Single Disc, FXSTS 1988-1999
Fits Harley Davidson FXSTS Springers. Uses factory axle anchor rod and bronze washers (not provided). Kit uses stock OEM master cylinder. Will not fit FLSTS (Oldboy).
GMA 201ST
|
|
|
GMA 201ST |
GMA 201ST-B |
GMA 201ST-C |
Classic Clear Anodized |
Classic Black |
Classic Chrome |
|
|
GMA 201ST-SB |
GMA 201ST-SC |
Smooth Black |
Smooth Chrome |
|
Rear Softail® 1984-1986
This caliper kit is a direct bolt-on replacement which fits 1984-1986 Softail frames. Includes all mounting hardware, spacers and bracket. The bracket is black anodized aluminum. Uses stock HD brake line. Will accept stock OEM master cylinder.
GMA 202ST
|
|
|
GMA 202ST |
GMA 202ST-B |
GMA 202ST-C |
Classic Clear Anodized |
Classic Black |
Classic Chrome |
|
|
GMA 202ST-SB |
GMA 202ST-SC |
Smooth Black |
Smooth Chrome |
|
Rear Softail 1987-1999
This caliper kit is a direct bolt-on replacement which fits 1987 to 1999 Softail® frames. Includes a one-piece black anodized bracket, eliminating the need for spacers. Clean and simple. Uses stock HD brake line. Will accept stock OEM master cylinder.
GMA 203, 204, 205
Rear Sportster Brake Kits
Each kit uses the same caliper and bracket. Correct brake line adapter fittings and axle spacers provided. All kits require a 5/8" bore Master Cylinder.
GMA 203 Rear Kit for HD Sportster 1979-1981
GMA 204 Rear Kit for HD Sportster 1982-Early 1987
GMA 205 Rear Kit for HD Sportster late 1987-1999
Shown above in Classic Black
*The words Harley-Davidson or HD are not intended to imply that any of these products are HD original equipment or are sanctioned by the Harley-Davidson company. The words are only used to identify products and models.
